inputs of pnr

 

I       INPUTS Of PNR:

The main inputs of PnR tool are:

Verilog netlist

Technology library

Synopsis design constrains

Physical Standard cell lib (LEF file)

Logical libs (.lib)

IO constrains file.(padframe.io)

Interconnect file(TLU+ file)

Table 1. input files formats and contents of the file

                       

 

2.1 Verilog Netlist:

At the gate level, the Verilog netlist gives the information about the logical functionality of the system in terms of logic gates (including complex gates and cells of the standard cell library).

This gate level Verilog netlist which is the output of the synthesis. The gate level netlist is technology dependent and it contains the standard cells, macros connected. The connection are based on RTL code of the block/IP/soc .

Contents of the netlist

· Logical connectivity (Std cells,Macros).

·  List of the nets.

·   Knowing connectivity by using Fly lines.

2.2 Technology Library:

The technology lib consists technology usage of the PnR tool. This gives the DRC (design rules check) rules to be done for each and every layout.It contains:

I.            Number and designation of the metals & vias.

II.            Physical & electrical information of the metals & vias.

III.            Physical char:  Min width, Min area, height

IV.            Electrical char: current density is present

V.            Units, precisions about the layers & via

VI.            Colors, pattern about layers & via

VII.            Physical design rules of the  layers & via

VIII.            Design rule such as wire to wire spacing, min width of the layers & vias.

 

2.3 Logical Library: (Verilog Description Or Tlf Or Lib):

Verilog is required for dynamic simulation. Pnr tools usually can use TLF.Verilog description should support back annotation for timing information.Transistor and interconnect parasitics are extraction done using STARRC (synopsis tool)  or other extraction tools. This done by using the characterization tool

Contents of the logical libs:

1.  Timing info  the Standard cells ,Soft macros , macros.

2.    functionality info of Standard cells,  macros.

3.    DRC like max transition ,max capacitance, max fanout.

4.    timing info of the cell are Cell delays ,Setup,Hold time

5.    Cell delay calculated based on the of input transition and output load.which will be present in the LUT(look up table)

6.    functionality is helpful Optimization Purpose & also Contain Power information & leakage info for each and every cell

 

 

 

2.4 Interconnect Parasitic File:(Tlu+ File)

 

It is used in  parasitic extraction.contains the Layer/via cap and resistive information in look up table. TLU+ Files are generated from ITF files( contains Interconnect details).

 The contents of the file can be given as follows:

1.      R,C parasitics of both metal,vias (per unit length)

2.      The Net Delays are  calculated by using parasitic values (R,C parasitics)

3.      TLU+ files  these are extracted from .ITF file.

4.      For Loading TLU+ files we have to load three files .

5.      Those are Max Tlu+,Min TLU+,MAP file.

6.      the .ITF file and .tf file are mapped to MAP file maps

 

 

Fig2: LIB views files generation

 

2.5 Standard Constrains Design File: (Sdc)

Before optimizing the design we need to define the enivornment which a design can operate. The contents of sdc files are:

1) modes of the operation & PVT conditions

2)system interface characteristics input and output load , fanouts

3)WLM used to calculate the delay of the net

these include  information about the area , power and timing constrains of the design.

The constrain consists of the basically  SDC commands(TCL script)/conditions for the particular operating mode

The design constrains are of two types:

1)clock constrains

2)non_clock constrains

The clock constrains mainly consists of :

Clock definition

Clock info

I/O delays

Min/max dealy

Clock uncertainity

Clock transistion

Timing expections

The non_clock constrains mainly consists of :

Operating conditions

Wire load model

System interface

DRV

Area constrains

Power optimization info

Logical assignment.

 

Design_Constrains:(Implicit Constrains In Library)

 Table 2. contents of the SDC file

 

The  synopsis design constrains mainly consists of

1)version (optional)

2)design_constrains

3)units (optional)

4)comments(optional)

 

PVT or delay corners consists of the how delay to be calculated at each corner

These are calculated using NLDM,

The output is present in the timing.lib and the extraction rules.

 

There are different PVT corners in the chip:

1)slow corner

2) typical corner

3)fast corner

 

2.6 Physical Libraries: (Lef):

abstract view of the macro LEF, standard cell LEF, io LEF . the LEF contains the physical implementation of the library. the LEF consist of the information of the METAL CONNECTIONS, VIA CONNECTIONS and the METAL BLOCKAGES information about the cell. This give info of the pin connection and layers.  The LEF file is readable ASCII format.

 

The LEF file gives info of :

Cell name, cell shape,size, orientation of the cell

Ports,pins in the layout gemotries

obstruct and blockages in the cell.

Antenna Diff .area

Height of the standard cell

Routing blockages

Pin information

 

 Example:

Lef File:

VERSION 5.6 ;

BUSBITCHARS "[]" ;

DIVIDERCHAR "|" ;

PROPERTYDEFINITIONS

 MACRO LEF58_EDGETYPE STRING ;

END PROPERTYDEFINITIONS

 

UNITS

 DATABASE MICRONS 1000 ;

END UNITS

 

MACRO P28_9T2V_SDFPRSQ_X10_PB10_HL

 CLASS CORE ;

 PROPERTY LEF58_EDGETYPE "EDGETYPE LEFT MULTIPLEHEIGHT ; EDGETYPE RIGHT MULTIPLEHEIGHT ;" ;

   SIZE 2.312 BY 1.800 ;

 SYMMETRY X Y ;

 SITE CORE9T_DV ;

 PIN CP

  DIRECTION INPUT ;

  USE SIGNAL ;

  PORT

   LAYER CA ;

    POLYGON 0.796 0.431 0.836 0.431 0.836 0.471 0.796 0.471  ;

   END

  PORT

   LAYER M1 ;

    POLYGON 0.637 0.475 0.788 0.475 0.788 0.373 0.849 0.373

 0.849 0.528 0.637 0.528  ;

   END

  ANTENNAGATEAREA 0.010200 ;

 END CP

 PIN D

  DIRECTION INPUT ;

  USE SIGNAL ;

  PORT

   LAYER CA ;

    POLYGON 0.660 0.380 0.700 0.380 0.700 0.420 0.660 0.420  ;

   END

  PORT

   LAYER M1 ;

    POLYGON 0.086 0.375 0.623 0.375 0.623 0.369 0.728 0.369

 0.728 0.425 0.086 0.425  ;

   END

  ANTENNAGATEAREA 0.012000 ;

 END D

 PIN Q

  DIRECTION OUTPUT ;

  USE SIGNAL ;

  PORT

   LAYER CA ;

    POLYGON 2.224 1.072 2.264 1.072 2.264 1.152 2.224 1.152  ;

   END

  PORT

   LAYER CA ;

    POLYGON 2.224 1.524 2.264 1.524 2.264 1.604 2.224 1.604  ;

   END

  PORT

   LAYER M1 ;

    POLYGON 2.212 1.450 2.233 1.450 2.233 1.200 2.216 1.200

 2.216 1.035 2.283 1.035 2.283 1.650 2.212 1.650  ;

   END

 END Q

 PIN RN

  DIRECTION INPUT ;

 

 Outputs of The Backend Design Flow:

  Post Route Netlist(.V):

The netlist gives the information about the standard cells pins connected to the nets.

At the gate level, the Verilog netlistgives the information of the logical functionality of the system in terms of the logic gates.

 Graphical Database System (.Gds File):

GDS II is a database file format of standard industry for data exchange  integrated circuit. It is binary file format.

Initially, GDS II was made as a used in photo mask plotting during fabrication. It has limited set of features and low data density. Present it is owned by Cadence Design Systems. GDS II is given to silicon foundries for IC fabrication.

GDS II files were placed on magnetic tapes. This moment was called "tape out”. these attributes used in manufacturing an integrated circuit, these are to reflect the way that the physical layout is designed.

  Design Exchange Format(.Def)

It is used represent  physical layout  layout in ASCII  format. It represents the netlist and circuit layout.we used DEF and LEF this represent complete layout while it being designed.

Originally def is designed by by the cadence design system.

The def file consists:

Core size/die size

List & locations of Components, Vias, Pins, Nets, Special nets Macros of the design

Placement information

Routing grids, power grids,preroute

Related to the metal blockage information

Pin location where it is interacted the with the outside world

Orientation

 

 Information of the DEF.Specifies the component has a location and cannot be moved by tools, but can be moved using specific commands.

Metal Fill Details

Tracks helps during Routing.

DEF contains the information about the layer above the Metal1. And that the reason it's Used in Digital Design.

def consists of the following information:

 

2.10 Standard parasitic format (spef file):

Cadence Design Systems standard for defining netlist parasitic. They are two forms of SPF are DSPF and RSPF; the term SPF itself is representing parasitic in general.

 

General Syntax

A typical SPEF file will 4 main sections

  header,

 name map ,

 top level port  and

 main parasitic description .

 

2.11 Standard delay format (sdf file):

What is SDF:

 SDF (Standard Delay Format) is interpretation cell timing of the data. The American Standard Code for Information Interchange (ASCII) data in the SDF file.  this SDF is  independent of any tool and language.

SDF gives information about

1.      Path delays

2.      Interconnect delays

3.      Timing constraints

4.      Technology parameters affecting delays

5.      Cell delays.

 

SDF file is also used in the back annotation of delays with the gate level simulations for getting behavior on chip.

 

Type of timing related Information

Delays:

Path delay,

Device delay

Interconnect delay,

Port delay

 

Naming Convention of SDF file:

As such there is no specific naming convention of SDF files.

 

Requirement of SDF:

 you are  writing  SDF file manual or if you are using a already written SDF file in your design, there are two main things you need to take care:

 

 Continuty between SDF file and design Description.

·Continuty Between SDF file and timing Models.

 Sample SDF file:

 (DELAYFILE // Header Section

(SDFVERSION "4.0")

(DESIGN "MYDESIGN")

(DATE "March 15, 2011 09:00")

(VENDOR "SYNOPSYS_MAGMA")

(PROGRAM "Timing Tool")

(VERSION "1.2a")

(DIVIDER /)

(VOLTAGE 1.2:1.0:0.8)

(PROCESS "best:nom:worst")

(TEMPERATURE -40:25:125)

(TIMESCALE 100 ps)

(CELL // Cell 1

(CELLTYPE "MYDESIGN")

(INSTANCE top)

(DELAY

(ABSOLUTE

(INTERCONNECT mck b/c/clk (.6:.7:.9))

(INTERCONNECT d[0] b/c/d (.4:.5:.6))

)

)

)

(CELL // Cell 2

(CELLTYPE "AND2")

(INSTANCE top/b/d)

(DELAY

(ABSOLUTE

(IOPATH a y (1.5:2.5:3.4) (2.5:3.6:4.7))

(IOPATH b y (1.4:2.3:3.2) (2.3:3.4:4.3))

)

)

)

(CELL // Cell 3

(CELLTYPE "DFF")

(INSTANCE top/b/c)

(DELAY

(ABSOLUTE

(IOPATH (posedge clk) q (2:3:4) (5:6:7))

(PORT clr (2:3:4) (5:6:7))

)

)

(TIMINGCHECK

(SETUPHOLD d (posedge clk) (3:4:5) (-1:-1:-1))

(WIDTH clk (4.4:7.5:11.3))

)

)

(CELL // Cell4.. Cell n

. . .

)


Comments

Popular posts from this blog

Physical design Design Flow